volvo ec35 excavator problems and solution. Volvo EC35 excavator can be designed to handle the toughest jobs you will ever run into, from massive open pit material handling to narrow trenching. The Volvo EC35 has been designed with a compact structure and controls which allows it to work in small sites such as in underground mines. In addition, the Volvo EC35 excavator is able to work in performing heavy-duty work for hours due to its smooth, low-maintenance engine for increased productivity.
The volvo ec35 excavator fuel pump is out of order
I have a Volvo ec35 and the fuel pump is acting up. The machine will start, run for about 5 seconds and then shut off. I have replaced the fuel pump and the problem still exists. I have also replaced all of the fuel lines, filters and both injectors and the problem still exists. When I turn the key on, you can hear the fuel pump pressurize the system. The check engine light does not stay on, but it flashes a couple of times when I turn the key on.
I noticed that when I put it into service mode, it shows an error code of “4002”. But when I look up that code in either my manual or online, they all say that it means “no codes”.
I am at a loss as to what could be causing this issue. Any help would be greatly appreciated!
volvo ec35 excavator Fuel system leakage
1. Check the fuel supply line for leakage and whether the tightness of each joint is qualified;
2. If there is a leak at the joint, tighten the screw or replace the fuel supply line;
3. The fuel return pipe has a large amount of fuel when it leaks, so you should check if there is any leakage in the return pipe after each cylinder injects fuel, and find out whether the leakage is caused by the loose pipe or the nozzle needle valve sealing ring has been worn;
4. The high-pressure oil pump leaks oil because its outlet end cover gasket leaks oil or its piston seal ring leaks oil;
5. Check if there is any dirt on the cooling water surface of the high-pressure oil pump; if so, clean it up;volvo ec35 excavator Engine piston and cylinder wear
The volvo ec35 excavator engine is out of order
The Volvo EC35 Excavator Engine is out of order! I think it needs to be replaced. The reason why I say this is because the engine overheated and caused the engine to shut down. The engine should be operating at a temperature of about 195 degrees, but the engine overheated to about 360 degrees.
The best way to fix the problem is to replace the entire engine. A new engine will be at least four hundred dollars and that does not include labor charges
The Volvo EC35 Excavator Engine is out of order! I think it needs to be replaced. The reason why I say this is because the engine overheated and caused the engine to shut down. The engine should be operating at a temperature of about 195 degrees, but the engine overheated to about 360 degrees.
The best way to fix the problem is to replace the entire engine. A new engine will be at least four hundred dollars and that does not include labor chargesThe volvo ec35 excavator lubricating oil in the engine is dirty
Cracked volvo ec35 excavator belt teeth or missing teeth
Volvo excavator teeth are the most easily damaged parts on the Volvo excavator, and they are also the most important parts of excavating the soil. Therefore, in use, we must pay attention to the protection of Volvo excavators.
Cracked volvo ec35 excavator belt teeth or missing teeth
In general, when using a Volvo excavator, it will be evaluated by its impact force, digging force and arm digging force, so as to meet the requirements of different operations. This can be achieved through various structural improvements. And this is where we need to consider the protection of the Volvo excavator.
The strength of the Volvo EC35 excavator’s bucket is an important factor affecting work efficiency, and there are many factors that affect it. How to improve the strength of the bucket is an important issue in improving work efficiency.
The timing volvo ec35 excavator belt is too loose or too tight
The timing volvo ec35 excavator belt is too loose or too tight, if the belt is too loose, will make the engine power loss and excessive fuel consumption; if the belt is too tight, will cause the tensioner to fail in advance. The correct adjustment method: adjust the belt so that when squeezed by hand in a certain position of the length of its vibration (the vibration amplitude is generally 10-20mm), at this time, with fingers gently knock on any part of the belt, should be able to hear the crisp sound.
The timing volvo ec35 excavator belt is too loose or too tight, resulting in damage to the engine and other components.
The timing volvo ec35 excavator belt is too loose, causing slippage and excessive wear of the belt and pulley; the belt is too tight, causing excessive wear of the pulley bearing.
The ideal tension of the timing volvo ec35 excavator belt is that it can be pressed down by 20 to 30mm when pressed with a finger at a certain point; at this time, there should be no obvious swinging or vibration in the middle part of the belt.
Volvo ec35 excavator problems and solution
If you want to learn about the Volvo ec35 excavator problems and solution, you should know that this is an extremely popular piece of heavy equipment, but it has a few issues. If you are interested in learning more about these issues and how they can be fixed, keep reading on. In this article, we will talk about some common problems that you will face with your Volvo ec35 excavator. The first problem that you might encounter is a hydraulic problem. This means that the hydraulic system will not function properly because the pump is clogged or blocked. If this happens to you, the best thing that you can do is to take it to a professional who can fix it for you.
1. Check if the fuel is sufficient
2. Check if the fuel line is unblocked
3. Check the air intake system of the diesel engine
4. Check whether the oil level of the fuel injection pump is appropriate
5. Check whether the fuel line connection is firm
6. Check whether there is water in diesel oil